• Chapter 1 Important information
    • Safety warnings
    • Product warnings
    • Regulatory notices
      • Water ingress
      • Disclaimer
      • EMC installation guidelines
      • Suppression ferrites
      • Connections to other equipment
      • Declaration of conformity
      • IMO and SOLAS
      • Warranty registration
      • Product disposal
      • Technical accuracy
      • Publication copyright
  • Chapter 2 Document information
    • 2.1 Applicable products
    • 2.2 Product documentation
      • Printed (hardcopy) product manuals
    • 2.3 Document illustrations
  • Chapter 3 Product and system overview
    • 3.1 Product overview
    • 3.2 Compatible transducers
      • Instrument Wind Vane transducer
      • Instrument Rotavecta transducer
    • 3.3 System protocols and cable systems
    • 3.4 SeaTalk 1
      • SeaTalk 1 connection
    • 3.5 SeaTalk NG
      • SeaTalk NG connection
    • 3.6 NMEA 2000
      • NMEA 2000 network connection
  • Chapter 4 Parts supplied
    • 4.1 Parts supplied
    • 4.2 Inline fuse requirement
  • Chapter 5 Product dimensions
    • 5.1 Product dimensions
  • Chapter 6 Location requirements
    • 6.1 Warnings and cautions
    • 6.2 General location requirements
    • 6.3 EMC installation guidelines
    • 6.4 Compass safe distance
    • 6.5 Viewing angle considerations
    • 6.6 Wind transducer location requirements
      • Wind vane transducer and Rotavecta mounting
  • Chapter 7 Mounting
    • 7.1 Tools required
    • 7.2 Removing the front bezel
    • 7.3 Mounting
  • Chapter 8 Cables and connections — General information
    • 8.1 General cabling guidance
      • Cable types and length
      • Cable routing
      • Strain relief
      • Cable shielding
      • Suppression ferrites
      • Connecting cables
      • Bare-ended wire connections
    • 8.2 Connections overview
      • Replacing spade terminals
  • Chapter 9 Network connections
    • 9.1 Transducer connection options
      • Direct transducer connection
      • iTC-5 transducer connections
      • Transducer pod connections
    • 9.2 SeaTalk 1 connection
    • 9.3 SeaTalk NG connection
      • Connecting SeaTalk NG cables
    • 9.4 NMEA 2000 network connection
  • Chapter 10 Power connections (SeaTalk NG connections)
    • 10.1 Power options
    • 10.2 SeaTalk NG power connection
    • 10.3 SeaTalk NG power supply
    • 10.4 Inline fuse requirement
    • 10.5 Inline fuse and thermal breaker ratings
    • 10.6 SeaTalk NG power cables
    • 10.7 SeaTalk NG product loading
    • 10.8 SeaTalk NG power connection point
    • 10.9 SeaTalk NG system loading
    • 10.10 Power distribution — SeaTalk NG
    • 10.11 Power connection via Autopilot Control Unit (ACU-Series)
  • Chapter 11 Power connections (SeaTalk 1 connections)
    • 11.1 Power options
    • 11.2 SeaTalk 1 power connection
    • 11.3 Inline fuse requirement
    • 11.4 Inline fuse and thermal breaker ratings
  • Chapter 12 Power connections (Direct connections)
    • 12.1 Power options
    • 12.2 Direct power connection
    • 12.3 Inline fuse requirement
    • 12.4 Inline fuse and thermal breaker ratings
    • 12.5 Power distribution
    • 12.6 Power cable extension (12 / 24 V systems)
  • Chapter 13 Getting started
    • 13.1 Controls
    • 13.2 Switching on the display
    • 13.3 Switching off the display
    • 13.4 Calibration alert
    • 13.5 Data master
      • Checking the software version and instrument status
  • Chapter 14 Calibration
    • 14.1 Calibration
    • 14.2 User calibration
      • Automatic Linearization
      • Aligning the wind transducer
      • Selecting the unit of measure for wind speed readings
    • 14.3 Intermediate calibration
      • Checking the software version and instrument status
    • 14.4 Dealer calibration
      • Setting access to the User Calibration Menu
      • Setting the response delay for Wind Angle readings
      • Setting the response delay for Wind Speed readings
      • Setting the response delay for VMG readings
      • Setting the wind speed Calibration Factor
      • Enabling and disabling Boat Show Mode
      • Resetting the display to factory defaults
  • Chapter 15 Using your display
    • 15.1 Pages
      • Changing pages
    • 15.2 i60 Wind operation
      • Display information
      • Using the display button
      • Using Tack and VMG buttons
      • True and Apparent wind
      • Switching between true and apparent wind information
    • 15.3 Illumination
      • Adjusting the backlight level
      • Adjusting the contrast
      • Group illumination
  • Chapter 16 Alarms
    • 16.1 Alarms
      • Instrument alarms
      • Alarm indications
      • Silencing alarms
      • Enabling / Disabling alarms
      • Setting alarm thresholds
  • Chapter 17 Maintaining your display
    • 17.1 Service and maintenance
    • 17.2 Routine equipment checks
    • 17.3 Cleaning the display case
    • 17.4 Cleaning the display screen
  • Chapter 18 Troubleshooting
    • 18.1 Troubleshooting
    • 18.2 Instrument troubleshooting
    • 18.3 Power up troubleshooting
    • 18.4 Miscellaneous troubleshooting
  • Chapter 19 Technical support
    • 19.1 Raymarine technical support and servicing
    • 19.2 Checking the software version
  • Chapter 20 Technical specification
    • 20.1 Physical specification
    • 20.2 Power specification
    • 20.3 Network specification
    • 20.4 Environmental specification
    • 20.5 Display specification
    • 20.6 Conformance specification
  • Chapter 21 Spares and accessories
    • 21.1 Spares
    • 21.2 Accessories
    • 21.3 SeaTalk NG cables and accessories
  • Appendix A NMEA 2000 PGNs
  • Appendix B Software release history
  • Blank Page
  • Blank Page